側裝和頂裝磁浮子液位計Side-mounted and top-mounted magnetic float level
磁翻板液位計是現場液位顯示儀表。它是一種多功能儀表，是玻璃板（管）液位計的更新?lián)Q代產品。液位顯示部位寬、醒目、無顯示盲區、可遠距離觀測，使用過程中不會出現泄露現象。它既能實現現場液位顯示，又能實現4-20mA遠傳，并配有液位報警開關。適用于一﹑二﹑三類壓力容器及工藝過程控制的液位顯示，并可用于易燃、易爆和有毒環境中。
結構原理：
BDCFZ現場顯示型磁翻板液位計主要有磁浮子、立管和指示器構成，磁性浮子在立管內與液位同步浮動，浮子中的磁鋼通過磁耦合作用驅動指示器上的磁翻板同步轉動變換顏色，紅色顯示液相，白色顯示氣相，紅白界面就是容器內的實際液位。
報警開關是磁浮子液位計專用的自保持型于簧管開關，將其安裝在
磁浮子液位計的立管上相應的報警位置。浮子隨液體上升和下降，感應相應的報警開關實現報警控制。
遠傳變送器是安裝在磁翻板液位計的立管上，由于浮子隨液位上下浮動使干簧管繼電器對信號電阻進行切換，隨變送器電路輸出與液位相應的DC 4～20mA標準信號。
技術參數：
環境溫度：-25～70℃
相對濕度：＜85%
測量范圍：500～8000mm
精 度：±10㎜
工作壓力：1.0、1.6、2.5、4.0、6.4、10、16 MPa
試驗壓力：1.5倍工作壓力
介質溫度：-196～350℃
介質粘度：≤0.15Pa·S
介質比重：≥0.5 g/cm3、
介面比重差：≥0.35 g/cm3
連接法蘭公稱通徑：DN20
連接法蘭標準： HG-20592
The liquid level is displayed by the programmed control, and it can be used in flammable, explosive and toxic environments.
Structural principle:
The BDCFZ on-site display type magnetic flap level gauge is mainly composed of a magnetic float, a standpipe and an indicator. The magnetic float floats synchronously with the liquid level in the standpipe. The magnetic steel in the float drives the magnetic flap on the indicator to rotate synchronously and change colors. The red color indicates the liquid phase, the white color indicates the gas phase, and the red-white interface represents the actual liquid level in the container.
The alarm switch is a self-holding type spring tube switch specifically for magnetic float level gauges. It is installed at the corresponding alarm position on the standpipe of the magnetic float level gauge. As the float rises and falls with the liquid, it senses the corresponding alarm switch to achieve alarm control.
The remote transmission transmitter is installed on the standpipe of the magnetic flap level gauge. As the float floats up and down with the liquid level, the bimetal relay switches the signal resistance, and the output of the transmitter circuit changes accordingly to provide a DC 4-20mA standard signal corresponding to the liquid level. Technical Specifications:
Environmental temperature: -25 to 70℃
Relative humidity: < 85%
Measurement range: 500 to 8000mm
Accuracy: ±10mm
Working pressure: 1.0, 1.6, 2.5, 4.0, 6.4, 10, 16 MPa
Test pressure: 1.5 times working pressure
Medium temperature: -196 to 350℃
Medium viscosity: ≤ 0.15 Pa·S
Medium density: ≥ 0.5 g/cm³
Interface density difference: ≥ 0.35 g/cm³
Connection flange nominal diameter: DN20
Connection flange standard: HG-20592
